Search results for "Plate electrode"

Template electrodeposition and characterization of nanostructured Pb as a negative electrode for lead-acid battery

2019

Abstract Despite Lead Acid Battery (LAB) is the oldest electrochemical energy storage system, diffusion in the emerging sectors of technological interest is inhibited by its drawbacks. The principal ones are low energy density and negative plate sulphating on high rate discharging. In this work, it is shown the possibility of overcoming such drawbacks by using nanostructured lead as a negative electrode. Lead nanowires (NWs) were fabricated by electrochemical deposition in template, which is an easy, cheap, and easily scalable process. Their morphology and crystal structure have been characterized by electron microscopy and X-ray diffraction, respectively. An electrochemical cell simulating…

EQCM and EIS studies of Znaq2++2e−⇄Zn0 electrochemical reaction in moderated acid medium

2003

The zinc electrodissolution and electrodeposition have been studied by means of electrochemical quartz crystal microbalance and electrochemical impedance spectroscopy. Relevant information on the mechanism of these electrochemical processes is provided by the analysis of experimental data. The zinc electrodeposition takes place with an important participation of hydrogen ions while the zinc electrodissolution occurs, in these experimental conditions, by a mechanism in two steps. Besides, it is proved that the presence of molecular oxygen in the solution contributes to the formation of a passive layer on the metallic zinc deposit.

Nanostructured lead-acid negative electrode with reduced graphene oxide

2021

Aim of this work is to develop a new nano-structured and nano-composite lead acid negative electrode with reduced graphene oxide (rGO). Nanostructured electrodes are fabricated by template electrodeposition of lead nanowires on a lead current collector. A polycarbonate track-etched membrane was used as a template (200 nm mean pores diameter). rGO was deposited on the nanostructured electrode from a graphene oxide (GO) dispersion in acetate buffer solution (ABS) (0.2 g/L). Potentiostatic deposition of rGO at -0.8 V vs. standard calomel electrode (SCE) was performed. Electrode with rGO was tested as negative electrode in cell with 5M sulfuric acid solution, a commercial pasted positive plate,…

Anodic alumina membranes as template for the synthesis of 1-D metal oxide and hydroxide nanostructures

2008

Anodic alumina membranes with highly ordered cylindrical pores and tuneable geometry have been prepared (pore diameters=20−200 nm; pore density 1012-1014 pores/m2; thickness: 20-100 mm) by controlling the anodizing process of aluminum in phosphoric, oxalic and sulphuric acid. The influence of different parameters (initial treatment of aluminium surface, composition of electrolyte, temperature and applied potential) on the final characteristics of the membranes have been investigated. The use anodic alumina membranes as template for the electrosynthesis of some metal hydroxides and oxides 1-D nanostructures (nanowires and nanotubes) will be also proved.

High-performance of PbO2 nanowire electrodes for lead-acid battery

2014

Abstract PbO2 nanowires were obtained by template electrodeposition in polycarbonate membranes and tested as positive electrode for lead-acid battery. Nanowires were grown on the same material acting as current collector that was electrodeposited too. The nanostructured electrodes were assembled in a zero-gap configuration using commercial negative plate and separator. Cell performance was tested by galvanostatic charge/discharge cycles in a 5 M H2SO4 aqueous electrolyte. PbO2 nanostructured electrodes were able to deliver at 1C rate an almost constant capacity of about 190 mAh g−1 (85% of active material utilization), close to the theoretical value (224 mAh g−1). The nanowire array provide…

Nanostructured Lead Electrodes with Reduced Graphene Oxide for High-Performance Lead–Acid Batteries

2022

Nanostructured Pb electrodes consisting of nanowire arrays were obtained by electrodeposition, to be used as negative electrodes for lead–acid batteries. Reduced graphene oxide was added to improve their performances. This was achieved via the electrochemical reduction of graphene oxide directly on the surface of nanowire arrays. The electrodes with and without reduced graphene oxide were tested in a 5 M sulfuric acid solution using a commercial pasted positive plate and an absorbed glass mat separator in a zero-gap configuration. The electrodes were tested in deep cycling conditions with a very low cut-off potential. Charge–discharge tests were performed at 5C. The electrode wi…

Elettrodo al piombo, metodo per la sua realizzazione ed accumulatore comprendente l’elettrodo

2011

Fabrication of CZTSe/CIGS Nanowire Arrays by One-Step Electrodeposition for Solar-Cell Application

2021

The paper reports some preliminary results concerning the manufacturing process of CuZnSnSe (CZTSe) and CuInGaSe (CIGS) nanowire arrays obtained by one-step electrodeposition for p-n junction fabrication. CZTSe nanowires were obtained through electrodeposition in a polycarbonate membrane by applying a rectangular pulsed current, while their morphology was optimized by appropriately setting the potential and the electrolyte composition. The electrochemical parameters, including pH and composition of the solution, were optimized to obtain a mechanically stable array of nanowires. The samples were characterized by scanning electron microscopy, Raman spectroscopy, and energy-dispersion spectros…

Metodo di realizzazione di un elettrodo ad elevata densità energetica ed elettrodo ottenibile con tale metodo

2010

Fabrication and characterization of nanostructured Ni and Pd electrodes for hydrogen evolution reaction (HER) in water-alkaline electrolyzer

2017

In the field of water-alkaline electrolyzer, the development of nanoporous low cost nickel electrodes is one of the potential approaches to increase electrocatalytic activity. Template electrodeposition is a facile and cheap technique for obtaining Ni nanowires (NWs) with high surface area. These nanostructures were fabricated by a two-step procedure. In the first step, a Ni compact layer was deposited on one side of the template where a gold film was previously sputtered, while, in the second-step, an ordered array of Ni-NWs was obtained by electrodeposition inside the template channels. The NWs were firmly connected to the underlying Ni layer, acting as a current collector. In order to en…